Jump to content

Issue with Sexout/SexoutSpunk


Recommended Posts

Posted

So, I've just downloaded SexOut (NG, SCR, NVSE Extender, NVSE). Alongside these, I downloaded MCM, the Pregnancy Mod, and SexoutSpunk. The game boots up normally, but when I load a save, the save opens and a small notice appears indicating that Spunk requires NVSE, the extender, and SexoutNG to work and that the game will now quit out. A few seconds pass, and the game closes. 

I've been racking my brain to see if I could remember doing anything wrong- nothing seems to ring. I've looked over NMM and FOMM and nothing seems out of place. I've included screenshots of my data folder, game folder, and FOMM and NMM just for reference.

I'll also note that the game starts fine if I turn Spunk off, but since my other mod requires it, I'd rather not do that.

post-275444-0-49215900-1430812382_thumb.png

post-275444-0-24718400-1430812383_thumb.png

post-275444-0-23768800-1430812384_thumb.png

post-275444-0-23945200-1430812385_thumb.png

post-275444-0-27607300-1430812386_thumb.png

Posted

ok you need to  read the docs more carefully,  make sure you have the minimum requirements, and that they are installed in the correct locations.

Common problems

------------------------

A common problem is that nvse on silverlock is not always the latest  beta version - spunk often has a link to the latest version on its home page.

 

Also make sure you put nvse extender(nx)in the correct locations it should go in data/nvse/plugins. Although I think its an fmod so just installed it with fomm or ,use 7zip to extract the contents and put then in the correct location.hope this helps .

 

Make sure spunk does not require the beta not stable version of NG as well.

 

Another possiblility is you have not set up the 4gb launcher correctly and its not launching nvse .Just launch nvse not 4gb to test this . The flags to set up the 4gn thingee,at least with my version of the 4gb thingee are a tad  confusing.

 

"C:\Program Files\Bethesda Softworks\Fallout New Vegas\fnv4gb.exe" -exe FalloutNV.exe -laaexe   .\FalloutNV.4GB -SteamAppID

 

FalloutNV.4GB <--- have you got thisin your data folder.

another think I think the steamAppID flag may vary depending on what version(country?) of FONV you have.Also I think from memory there is at least one fork /continuation of the 4gb thing, just for extra confusion . the 4gb can be a pain in the ass  to set up.

 

the 4gb thing can also be more tricky than this you may have to adjust your boot,ini  as well ... though microsoft in there wisdom has changed it name with windows 7+ :)

 

Also I think if you check the silverlock docs there is a console command that prints the nvse version to screen

Posted

ok you need to  read the docs more carefully,  make sure you have the minimum requirements, and that they are installed in the correct locations.

Common problems

------------------------

A common problem is that nvse on silverlock is not always the latest  beta version - spunk often has a link to the latest version on its home page.

 

Also make sure you put nvse extender(nx)in the correct locations it should go in data/nvse/plugins. Although I think its an fmod so just installed it with fomm or ,use 7zip to extract the contents and put then in the correct location.hope this helps .

 

Make sure spunk does not require the beta not stable version of NG as well.

 

Another possiblility is you have not set up the 4gb launcher correctly and its not launching nvse .Just launch nvse not 4gb to test this . The flags to set up the 4gn thingee,at least with my version of the 4gb thingee are a tad  confusing.

 

"C:\Program Files\Bethesda Softworks\Fallout New Vegas\fnv4gb.exe" -exe FalloutNV.exe -laaexe   .\FalloutNV.4GB -SteamAppID

 

FalloutNV.4GB <--- have you got thisin your data folder.

another think I think the steamAppID flag may vary depending on what version(country?) of FONV you have.Also I think from memory there is at least one fork /continuation of the 4gb thing, just for extra confusion . the 4gb can be a pain in the ass  to set up.

 

the 4gb thing can also be more tricky than this you may have to adjust your boot,ini  as well ... though microsoft in there wisdom has changed it name with windows 7+ :)

 

Also I think if you check the silverlock docs there is a console command that prints the nvse version to screen

Thanks. I'd simply gotten an outdated version of NVSE from Silverlock. Just me being stupid :P

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...